CNC Lathe 80 inch swing, hollow spindles to 32 inch,
Lathe, CNC Heavy Duty 3 Shear BedSwing | 80" |
Machining Length | 30' |
# Axis | 2 |
Chuck Size | 48" |
Bar Capacity | 12" |
Power | 60 hp |
Turning Dia | 66" |
Tailstock | Yes |
Control | CNC (Fanuc) |
SWING over bed 50 to 80 inch.
Hollow spindles up to 32 inch.
BED - Lengths available up to 12 meters.
Width................................mm (in.) 1100 (43.31)
CARRIAGE
Width of cross slide.................mm (in.) 600 (23.62)
TURRET
Standard tool post....................Auto 4-way / Polygon Disc / VDI disc
No. of tool stations..................H4;H6 / V12 / V8;V12
Turning Tool Size.....................mm (in.) 32 x 32 (1.25)
Boring Tool Size(max.)................mm (in.) 63 (2.5)
TRAVEL
Cross slide(X axis) travel............mm (in.) 700 (27.55)
Longitudinal(Z axis) travel...........mm (in.) 3000 (118.11), 4000 (157.48), 5000 (196.85),
6000 (236.22),7000 (275.59), 8000 (314.96),9000 (354.33), 10000 (393.70), 11000 (433.07), 12000 (472.44)
Cutting feed rate.....................mm(in.)/rev X axis : 0.001~250(0.00004~9.84) ; Z axis : 0.001~400(0.00004~15.75)
Rapid travel..........................M.(Ft.)/min X axis : 6(19.68) ; Z axis : 6(19.68)
Ballscrew diameter....................mm (in.) X axis : 50(1.96) ; Z axis : 80(3.14)
TAILSTOCK
Quill type............................Built-in type, Rotating tailstock quill
Quill diameter........................mm (in.) 235(9.25)
Quill travel..........................mm (in.) 200(7.87)
Internal taper of quill MT#6
MOTOR
Headstock oil refrigerator............18,000BTU(4,500Kcal)
Main spindle..........................KW(HP) 30/37(40/50)-STD. ; 37.5/45(50/60)-OPT.
Axis servo............................KW(HP) X axis : 7(9.387) ; Z axis : 7(9.387)
Hydraulic tank........................KW(HP) 3.7(5)
Coolant pump..........................KW(HP) 1.05(1.4)
Controller: FANUC 0i-TF series-STD ; FANUC 31i-B series / Other required-OPT.Note :
(1) X and Z axes actual cutting diameter will change when equipped with different turrets.
(2) Specifications are subject to change without notice for improvement
Standard Accessories
* Hydraulic H4 turret.
* Rotating tailstock quill with 235mm diameter.
* Motorized tailstock body and quill movement.
* FANUC 0i-TF series complete with manual guide and thread repair.
* Front and rear chip conveyor.
Swing | 80" |
Machining Length | 30' |
# Axis | 2 |
Chuck Size | 48" |
Bar Capacity | 12" |
Power | 60 hp |
Turning Dia | 66" |
Tailstock | Yes |
Control | CNC (Fanuc) |
SWING over bed 50 to 80 inch.
Hollow spindles up to 32 inch.
BED - Lengths available up to 12 meters.
Width................................mm (in.) 1100 (43.31)
CARRIAGE
Width of cross slide.................mm (in.) 600 (23.62)
TURRET
Standard tool post....................Auto 4-way / Polygon Disc / VDI disc
No. of tool stations..................H4;H6 / V12 / V8;V12
Turning Tool Size.....................mm (in.) 32 x 32 (1.25)
Boring Tool Size(max.)................mm (in.) 63 (2.5)
TRAVEL
Cross slide(X axis) travel............mm (in.) 700 (27.55)
Longitudinal(Z axis) travel...........mm (in.) 3000 (118.11), 4000 (157.48), 5000 (196.85),
6000 (236.22),7000 (275.59), 8000 (314.96),9000 (354.33), 10000 (393.70), 11000 (433.07), 12000 (472.44)
Cutting feed rate.....................mm(in.)/rev X axis : 0.001~250(0.00004~9.84) ; Z axis : 0.001~400(0.00004~15.75)
Rapid travel..........................M.(Ft.)/min X axis : 6(19.68) ; Z axis : 6(19.68)
Ballscrew diameter....................mm (in.) X axis : 50(1.96) ; Z axis : 80(3.14)
TAILSTOCK
Quill type............................Built-in type, Rotating tailstock quill
Quill diameter........................mm (in.) 235(9.25)
Quill travel..........................mm (in.) 200(7.87)
Internal taper of quill MT#6
MOTOR
Headstock oil refrigerator............18,000BTU(4,500Kcal)
Main spindle..........................KW(HP) 30/37(40/50)-STD. ; 37.5/45(50/60)-OPT.
Axis servo............................KW(HP) X axis : 7(9.387) ; Z axis : 7(9.387)
Hydraulic tank........................KW(HP) 3.7(5)
Coolant pump..........................KW(HP) 1.05(1.4)
Controller: FANUC 0i-TF series-STD ; FANUC 31i-B series / Other required-OPT.Note :
(1) X and Z axes actual cutting diameter will change when equipped with different turrets.
(2) Specifications are subject to change without notice for improvement
Standard Accessories
* Hydraulic H4 turret.
* Rotating tailstock quill with 235mm diameter.
* Motorized tailstock body and quill movement.
* FANUC 0i-TF series complete with manual guide and thread repair.
* Front and rear chip conveyor.