Heavy duty Lathe 45"- 60" Swing New
Lathes, Engine, CenterSwing | 1,165 mm |
Swing Options | 1165 -1530 MM |
Swing Over Cross Slide | 840 mm |
Swing Over Cross Slide Options | 840 - 1210 MM |
Centers | 4,000 mm |
Center Options | 1500 - 12000 MM |
Spindle Bore | 6" |
Spindle Bore Options | 6 - 30 inches |
PB series PB-45 PB-50 PB-60
Swing over bed 1,165mm 1,280mm 1,530mm
Swing over cross slide 840mm 950mm 1,210mm
Swing over gap 1,610mm 1,730mm 1,980mm
Distance between centers 1.500mm~12,000 mm in 40" increments
Spindle nose A2-11~A2-40
Spindle bore 6"~18" 6"~24" 7"~30"
Spindle motor Standard-30HP ; Option-40HP,50HP
DETAILS
BED WIDTH : 715mm (28.14")
ITEM UNIT PB-45 PB-50 PB-60
Centre height mm (in.) 590 (23.22) 650 (25.59) 775 (30.51)
Swing over bed mm (in.) 1165 (45.86) 1280 (50.39) 1530 (60.23)
Swing over cross slide mm (in.) 840 (33.07) 950 (37.40) 1210 (47.63)
Swing over gap mm (in.) 1610 (63.38) 1730 (68.11) 1980 (77.95)
Gap width from headstock(opt.) mm (in.) 600 (23.62)
Distance between centres mm (in.) 1500 (59.05), 2000 (78.74), 3000 (118.11),
4000 (157.48), 5000 (196.85), 6000 (236.22),
7000 (275.59), 8000 (314.96), 9000 (354.33),
10000 (393.70), 11000 (433.07), 12000 (472.44)
BED
Width (W/O auxiliary guide) mm (in.) 715 (28.14)
Width (W auxiliary guide) mm (in.) 800 (31.49)
CARRIAGE
Cross slide travel mm (in.) 800 (31.49)
Compound tool post travel mm (in.) 500 (19.68)
4-way tool post width mm (in.) 255 (10.03)
THREAD FEED RANGE
Longitudinal feed mm/rev (in.rev) 0.045~2.55 (0.0018~0.1)
Cross feed mm/rev (in.rev) 0.023~1.28 (0.0009~0.05)
Longitudinal rapid feed mm/rev (in.rev) 2000 (78.74)
Cross rapid feed mm/min (in/min) 1270 (50.00)
Metric thread mm (kinds) 1~56 (60)
Inch thread TPI (kinds) 1/2~28 (60)
Module thread MOD (kinds) 0.25~14 (60)
Diamteral pitch thread DP (kinds) 2~112 (60)
Pitch of leadscrew mm (TPI) 12 (2)
TAILSTOCK
Quill diameter mm (in.) 145 (5.70)
Quill travel mm (in.) 200 (7.87)
Inner taper of quill MT#6
Bearing surface on the bed ways mm (in.) 600 (23.62)
MOTOR
Main spindle motor KW (HP) 22(30)-STD.
29(40) / 37(50)-OPT.
Coolant pump motor KW (HP) 0.1 (0.125)
* 1 dead centre, MT #6.
* 2-speed tailstock quill (manual).
* One piece stainless steel leadscrew cover.
* Coolant pump.
* Follow type splash guard.
* Rear side chip and water collect plate.
* Thread chasing dial.
* Water and oil collect plate under apron.
* Work lamp.
Swing | 1,165 mm |
Swing Options | 1165 -1530 MM |
Swing Over Cross Slide | 840 mm |
Swing Over Cross Slide Options | 840 - 1210 MM |
Centers | 4,000 mm |
Center Options | 1500 - 12000 MM |
Spindle Bore | 6" |
Spindle Bore Options | 6 - 30 inches |
PB series PB-45 PB-50 PB-60
Swing over bed 1,165mm 1,280mm 1,530mm
Swing over cross slide 840mm 950mm 1,210mm
Swing over gap 1,610mm 1,730mm 1,980mm
Distance between centers 1.500mm~12,000 mm in 40" increments
Spindle nose A2-11~A2-40
Spindle bore 6"~18" 6"~24" 7"~30"
Spindle motor Standard-30HP ; Option-40HP,50HP
DETAILS
BED WIDTH : 715mm (28.14")
ITEM UNIT PB-45 PB-50 PB-60
Centre height mm (in.) 590 (23.22) 650 (25.59) 775 (30.51)
Swing over bed mm (in.) 1165 (45.86) 1280 (50.39) 1530 (60.23)
Swing over cross slide mm (in.) 840 (33.07) 950 (37.40) 1210 (47.63)
Swing over gap mm (in.) 1610 (63.38) 1730 (68.11) 1980 (77.95)
Gap width from headstock(opt.) mm (in.) 600 (23.62)
Distance between centres mm (in.) 1500 (59.05), 2000 (78.74), 3000 (118.11),
4000 (157.48), 5000 (196.85), 6000 (236.22),
7000 (275.59), 8000 (314.96), 9000 (354.33),
10000 (393.70), 11000 (433.07), 12000 (472.44)
BED
Width (W/O auxiliary guide) mm (in.) 715 (28.14)
Width (W auxiliary guide) mm (in.) 800 (31.49)
CARRIAGE
Cross slide travel mm (in.) 800 (31.49)
Compound tool post travel mm (in.) 500 (19.68)
4-way tool post width mm (in.) 255 (10.03)
THREAD FEED RANGE
Longitudinal feed mm/rev (in.rev) 0.045~2.55 (0.0018~0.1)
Cross feed mm/rev (in.rev) 0.023~1.28 (0.0009~0.05)
Longitudinal rapid feed mm/rev (in.rev) 2000 (78.74)
Cross rapid feed mm/min (in/min) 1270 (50.00)
Metric thread mm (kinds) 1~56 (60)
Inch thread TPI (kinds) 1/2~28 (60)
Module thread MOD (kinds) 0.25~14 (60)
Diamteral pitch thread DP (kinds) 2~112 (60)
Pitch of leadscrew mm (TPI) 12 (2)
TAILSTOCK
Quill diameter mm (in.) 145 (5.70)
Quill travel mm (in.) 200 (7.87)
Inner taper of quill MT#6
Bearing surface on the bed ways mm (in.) 600 (23.62)
MOTOR
Main spindle motor KW (HP) 22(30)-STD.
29(40) / 37(50)-OPT.
Coolant pump motor KW (HP) 0.1 (0.125)
* 1 dead centre, MT #6.
* 2-speed tailstock quill (manual).
* One piece stainless steel leadscrew cover.
* Coolant pump.
* Follow type splash guard.
* Rear side chip and water collect plate.
* Thread chasing dial.
* Water and oil collect plate under apron.
* Work lamp.